Metal Roof Repair in Bryan means finding the leak, securing the panel, and sealing it so it stays sealed. We handle standing seam, exposed fastener, and corrugated metal roofs across Bryan, Texas. Whether hail punched through a panel or a screw backed out and water is dripping into your attic, we get it dry. Same-day estimates, code-correct work, and a written warranty on every repair.
Tell us what is happening. Our local team will confirm your visit shortly.
Call Now (979) 316 9392 → No spam. No obligation. Just practical help.
Metal Roof Repair in Bryan is the process of restoring a metal roof's ability to shed water, which means locating the failure, correcting the panel or fastener, and sealing the penetration so it holds through the next storm. Metal roofs fail in predictable places: fastener grommets, panel laps, ridge caps, pipe boots, and valley flashing. We start with a moisture meter and infrared camera scan of the ceiling below, then walk the roof to match the wet spot to the actual breach. Most repairs involve replacing backed-out screws, resealing laps, and re-flashing a vent or chimney.
Bryan sits in a hail belt, and that matters. A single spring storm can dent panels, shear off fastener heads, and open seams that look fine from the ground. We see it constantly in 77803 and 77802, where older homes have metal roofs that have already survived two or three hail events. If you have water staining on a ceiling or a drip you hear at night, that is usually a fastener or flashing failure, not a panel that needs replacing. We diagnose it, fix the actual cause, and show you photos of what we found.
Every metal roof repair starts with a full diagnostic and ends with a water test. Here is what is covered in a standard repair visit. If we find something outside this scope, we show you the photo and quote it before we touch it.
We walk the roof, check every fastener, seam, and penetration, and scan the ceiling below with a moisture meter and infrared camera. You get photos of what we found and a clear explanation of the cause.
Backed-out, sheared, or rusted screws are replaced with gasketed fasteners matched to your panel profile. We set them to the correct depth so the gasket seals without crushing.
Failed sealant at panel laps and seams is removed and replaced with manufacturer-approved sealant. We clean the surface first so the new sealant bonds properly and lasts.
Chimney, vent, and valley flashing is re-seated or replaced. Flashing is the most common leak source on a metal roof, so we treat it as a priority, not an afterthought.
Lifted or shifted panels are re-seated and re-fastened. If a panel is damaged beyond repair, we replace it with a matching profile and color.
We water-test the repaired area, re-check the ceiling with the moisture meter, and give you a written warranty on the repair. You also get a maintenance note on what to watch for.
Call (979) 316 9392 or book online. We ask what you are seeing, where the water is showing up, and whether the roof is standing seam or exposed fastener. Most estimates are scheduled the same day or next morning. You get a two-hour arrival window, not a vague all-day promise.
A HAAG Certified Inspector walks the roof, checks fasteners, laps, flashing, and penetrations, and scans the ceiling below with a moisture meter and infrared camera. We photograph everything. If the leak is coming from a vent boot or chimney flashing rather than the panels, you will see exactly that.
You get a written scope with the repair method, materials, and price before we start. If we find a second issue while we are up there, we show you the photo and quote it separately. You decide. No pressure, no add-ons you did not approve.
Most metal roof repairs take two to five hours. We replace failed fasteners with gasketed screws, reseal laps and seams with approved sealant, re-flash penetrations, and re-seat any lifted panels. If decking is wet, we replace the damaged section so the new repair has solid material to anchor to.
We water-test the repaired area, re-check the ceiling with the moisture meter, and walk you through photos of before and after. You get a written warranty on the repair and a maintenance note telling you what to watch for. We clean up the site and haul off old fasteners and debris.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Reads moisture levels in decking and ceiling cavities so we can confirm the leak source and verify the repair dried the area out.
Shows temperature differences that reveal hidden moisture behind drywall and under panels, which helps us trace leaks we cannot see.
Drives fasteners quickly and consistently when we replace decking or secure new flashing. Correct depth matters on every fastener.
Applies manufacturer-approved sealant to seams, laps, and flashing. We use the right sealant for metal, not a generic caulk.
Lifts panel edges and flashing without damaging the metal so we can access the failure point and re-seat the panel correctly.
Keeps us stable and safe on steep metal pitches. A metal roof is slick when wet, and fall protection is not optional.
Clears debris, leaves, and granules from seams and gutters so sealant bonds and water can drain properly.
A 1940s home had a metal roof with a chimney that had been caulked three times over five years. Water was staining the ceiling in the room below, and the homeowner was told the roof needed full replacement.
We removed the old caulk, re-flashed the chimney with new metal and approved sealant, and water-tested the repair. The leak stopped. The repair cost $850 instead of the $18,000 replacement quote.
An April hailstorm sheared 40 fasteners on an exposed fastener metal roof. The homeowner had a ceiling stain and a drip in the attic but no visible damage from the ground.
We replaced all 40 fasteners with gasketed screws, resealed the seams, and documented the damage for the insurance claim. The adjuster approved the repair, and the leak stopped.
A wind storm lifted the edge of a standing seam panel and backed out six fasteners. The homeowner worried the panel would tear off in the next storm and called for an emergency repair.
We re-seated the panel, replaced the fasteners, and checked the rest of the roof. The repair took three hours. The roof is back to its wind rating and the panel is secure.
Most metal roof calls come down to a handful of failures. Here are the ones we see most often in Bryan, and what happens if you leave them alone.
Ask a pro →We trace the leak with a moisture meter and infrared camera, then repair the actual entry point, whether it is a fastener, a seam, or flashing. We water-test the repair before we leave and confirm the ceiling cavity is drying.
We replace failed fasteners with gasketed screws matched to your panel profile and set them to the correct depth. We check every fastener on the roof, not just the ones near the leak.
We replace cracked boots with new ones matched to your panel profile and seal them with approved sealant. The repair takes under two hours and stops the leak immediately.
We re-flash the joint with new metal and approved sealant. We do not just caulk over the old flashing. The new flashing is built to shed water, and we water-test it before we leave.
“We had a leak over the kitchen for two weeks. Two other companies wanted to replace the whole roof. These guys found a failed pipe boot and a backed-out fastener, fixed both in about three hours, and the ceiling has been dry since. They showed me photos of the crack in the boot. Honest work.”
Marcus T.Homeowner, Austin's Colony
✓ Verified“Our 1940s house has a standing seam roof that had been patched badly for years. They re-flashed the chimney, replaced the sealant with the right stuff, and re-seated two panels. The estimate was clear and the final price matched it. No surprise charges.”
Dana R.Homeowner, Historic Downtown Bryan
✓ Verified“Hail came through in April and dented our metal roof. Their inspector documented everything for the insurance claim, and the adjuster approved it without argument. They replaced four panels and all the damaged fasteners. Roof looks new and the claim was painless.”
Kevin S.Homeowner, Edgewater
✓ VerifiedMost metal roof repairs in Bryan run $250 to $1,200 in 2026, depending on access, panel type, and how many penetrations are involved. A single fastener reseal or pipe boot replacement sits at the low end. Re-flashing a chimney or replacing a section of damaged panel pushes toward the higher end. You get a written price before we start, and we do not add charges you did not approve.
Yes. We repair standing seam, exposed fastener, corrugated, and architectural metal roofs across Bryan and Brazos County. Most repairs are fastener replacement, seam resealing, and flashing correction. We also replace individual panels when hail or wind has damaged them beyond sealing. If your roof is repairable, we will tell you. If it is not, we will show you why.
Most metal roof repairs take two to five hours on site. A simple fastener or sealant repair can be done in under two hours. A panel replacement or chimney re-flash may take a full day. We schedule a two-hour arrival window and tell you upfront if the job needs more than one visit, which is rare.
Hail, wind uplift, and thermal expansion are the big three in Bryan. Hail dents panels and shears fastener heads. Wind backs screws out and lifts panel edges. Summer heat expands panels, and winter contraction works fasteners loose over time. Clogged gutters and failed pipe boots cause the rest. We check all of these on every diagnostic visit.
Roof RepairGeneral roof repair covers the same diagnostic process we use on metal roofs, applied to shingle, tile, and flat systems. If your home has a mix of roof types, we handle the whole roof in one visit.Explore →
Roof Leak RepairRoof leak repair is often the reason we are called to a metal roof. We trace the leak with a moisture meter and infrared camera, then fix the entry point rather than caulking over it.Explore →
Shingle Roof RepairShingle roof repair handles the asphalt side of your roof, including missing shingles, curling tabs, and hail damage. Many Bryan homes have metal on one section and shingles on another, and we repair both.Explore →
Flat Roof RepairFlat roof repair covers low-slope sections, including EPDM and TPO membrane. If your metal roof ties into a flat porch or addition, we repair the transition and the membrane together.Explore →
Tile Roof RepairTile roof repair addresses clay and concrete tile, which fail differently than metal. We repair cracked tiles, re-bed ridge caps, and correct flashing where a tile roof meets a metal section.Explore →
Emergency Roof RepairEmergency roof repair is for active leaks, storm damage, and exposed decking. We tarp and stabilize the roof first, then schedule the permanent metal repair. Call (979) 316 9392 for Emergency Metal Roof Repair Bryan TX.Explore →
Storm Damage Roof RepairStorm damage roof repair covers hail, wind, and debris damage. Our HAAG Certified Inspectors document the damage for insurance, then repair the metal panels, fasteners, and flashing to restore the roof.Explore →
Hail Damage Roof RepairHail damage roof repair targets dented panels, sheared fasteners, and cracked sealant. Bryan sits in a hail belt, so we see this every spring. We document the damage and repair or replace affected panels.Explore →We answer the phone, show up when we say we will, and fix the leak. Same-day estimates, written warranty, and code-correct work. Call (979) 316 9392 or book online.
Book a Repair (979) 316 9392 →Call us at (979) 316 9392 and you get a real person who can schedule your inspection, not a call center. We answer Monday through Friday from 8:00 to 18:00, and we run 24/7 for emergency roof repair in Bryan. Leave a message after hours and we call back first thing.